Heating System Repair in Santa Fe, NM
No heat or uneven heating in Santa Fe? We diagnose furnaces, boilers, and heat pumps and explain repair options. Call 505-316-4231 for availability.
If your home has no heat or some rooms stay cold, Lobo Tech can diagnose the heating system and explain the repair options. We service furnaces, boilers, and heat pumps in Santa Fe, checking the controls, heat source, and airflow or water circulation as appropriate. If you are unsure what type of heater you have, describe the problem when you call 505-316-4231.
Content reviewed 2026-10-01.
Finding the right diagnosis for your heater
Furnaces heat air and move it through ducts. Boilers heat water for radiators, baseboards, or radiant floors. Heat pumps use refrigerant to move heat. If you are unsure which system you have, a photo of the equipment and a description of the symptoms can help us plan the visit.
No heat or uneven room temperatures
Tell us whether the system is silent, starts and stops, blows cold air, or heats only part of the house. We check the controls and heat source, then trace airflow or water circulation to the affected rooms. A cold bedroom does not necessarily mean the whole heating system needs replacement.
Safety checks before repair
We check the safety controls and, on fuel-burning equipment, combustion and venting as appropriate. The diagnosis explains what failed and whether the system can be operated safely. Repairs are based on those findings, and replacement is discussed when the condition or repair cost makes it worth considering.
Name the machine before we name the part
Heating repair in this town might be a furnace, a boiler, a heat pump, baseboard, radiant, or a wall heater in a casita. The phone call should say which. “The heat is out” sends the wrong parts if we guess. If you do not know, tell us what the thermostat wires go to, or send a photo of the unit. We would rather see a blower and a gas valve than hear “the heater.”
Diagnosis before the parts cannon
A furnace that does not start can be a thermostat, a condensate switch, a pressure switch, an igniter, a flame sensor, or a control board. Those parts have an order. We do not replace all of them because the truck is stocked. We test the one that failed. Boards get blamed for dirty flame sensors. Igniters get blamed for a pressure switch that will not close because the vent is blocked. The vent in Santa Fe includes ice, a bird, and a vent that was reduced during a reroof.
Safety items we will not bypass
A roll-out switch that has tripped means flame went where flame should not go. We find out why. We do not jumper it. A heat exchanger that is cracked is a condemnation, not a cleaning. A gas valve that will not shut is a shutoff at the appliance valve and a replacement, not a “turn it off at the thermostat.” Carbon monoxide in the supply air ends the visit as a repair and starts it as a do-not-run. We leave the system off and we say that in writing.
The repair versus the replacement conversation
We put both numbers down when the equipment is old enough that the question is fair. A $400 igniter on a 22-year-old furnace is still the right repair if the exchanger is intact and you want another few seasons. A $400 igniter on a furnace with a cracked exchanger is wasted. We will not push the replacement to make the ticket larger, and we will not hide the age to make the repair look smarter than it is. You decide with both numbers.
After it is running
Temperature rise on a furnace, or the loop actually getting hot on a boiler, before we leave. A system that “comes on” and produces lukewarm air is not finished. Filter, vent, and the thermostat schedule if the house was simply set to hold 55. We see that more than anyone wants to admit. Call 505-316-4231. If you suspect a gas leak, leave the area immediately. From a safe location outside, call New Mexico Gas Company at 1-888-664-2726 or 911. Do not use switches or electronics, try to find or stop the leak, or return until emergency responders say it is safe.
Triage on the phone
If you suspect a gas leak, leave the area immediately. From a safe location outside, call New Mexico Gas Company at 1-888-664-2726 or 911. Do not use switches or electronics, try to find or stop the leak, or return until emergency responders say it is safe. If a CO alarm sounds, get everyone outside to fresh air and call 911. Stay outside until emergency responders say it is safe to return. No smell and no heat, and we ask what the machine is and what it is doing: silent, clicking, blowing cold, blowing warm for a minute and stopping. Those four answers are four different parts. A photo of the front of the unit and of the thermostat saves a return trip to the truck. If you have already replaced the thermostat and it changed nothing, say that. We will not sell you a second thermostat.
In the closet
We watch a full call for heat. We do not yank parts during the sequence. When it stops, the meter goes on the part that stopped it. Condensate safety switches get a look on every condensing furnace because they are the most common “dead furnace” in a house that also has a slightly clogged drain. Vents get a look because birds and reroofs are common here. The repair is the failed part plus the reason it failed, if the reason will kill the new part. A flame sensor on a sooted burner is a cleaning and a sensor, not just the sensor.
Written result
What failed, what we replaced, what we recommend and did not do. If the exchanger is in question we say inspected or not inspected. We do not write “serviced” as if that word meant safe. Temperature at a supply register before we leave, so “it runs” is not the only test. After-hours premium is on the invoice as its own line if it applied. 505-316-4231. License 384927. If the heat is a boiler or baseboard, say so and you will get the person thinking about water, not a blower.
Testing before replacing heating components
The sequence is the diagnosis. Thermostat, safeties, inducer or pump, ignition or burner, airflow or circulation, then the expensive board. We say which step failed. A dirty flame sensor, a clogged condensate switch, a bird in the vent, and a cracked exchanger are four different endings and only one of them is a new furnace. You get the ending we found, plus a price. If the equipment is old and the repair is a large fraction of a replacement, you also get the replacement number so you are not choosing blind. We do not jumper rollout or limit switches to “get you through the night” and leave a hazard. CO in the supply air ends the visit with the system off. If you suspect a gas leak, leave the area immediately. From a safe location outside, call New Mexico Gas Company at 1-888-664-2726 or 911. Do not use switches or electronics, try to find or stop the leak, or return until emergency responders say it is safe. Boilers and furnaces both get called “the heater.” Say which, or send a photo. Baseboard and radiant systems need checks of their own controls, circulation, and heat supply. Tell us which type you have so we can plan those checks. After-hours is for houses that are actually cold or unsafe, and the premium is said first. 505-316-4231. License 384927. The note we leave names the part and the reading, not the word “serviced.”
Describe the heating symptoms when you call
Silent is power, a switch, or a stat. Clicking with no flame is ignition or a safety. Flame that lights and dies is the sensor or the flame. Blower that runs cold is the burner not firing or a heat pump in the wrong mode. Blower that runs hot and then stops is a limit, a filter, or an exchanger that should not be run. Water on the floor in front of a condensing furnace is the drain, and it will shut the furnace down on purpose. Those observations help us prepare for the visit. If you are unsure how to describe it, a photo of the equipment and thermostat can help. Add the photo. If an alarm sounded, say alarm. We treat that as combustion until we prove otherwise, and we do not reset and leave. The price is the part we prove, plus the premium if you wanted us at night and we told you the premium first. Morning is a fair offer when the house is safe and merely cool.
What we actually get called for
Common problems we diagnose and repair in Santa Fe homes.
Air blows but stays cold
We check the heat source, controls, and operating mode to find why heat is not reaching the air.
The system starts and stops
A safety shutdown, restricted airflow, or control problem may be involved.
Some rooms stay cold
We check ducts or heating zones as appropriate to the system.
Boiler pressure is low
We check for leaks and problems with the fill assembly or expansion tank before adding parts.
How a job runs
Identify the system and symptoms
Tell us what the heater does when it tries to start and which rooms are affected.
Diagnose and quote
We test the relevant controls and components, then explain the repair and parts availability.
Repair and verify operation
We check the heating cycle after the work and discuss replacement only where the findings support it.
Questions people ask before they call
Can you come tonight if the heat is out?
We offer emergency heating service, subject to current availability and parts. Call 505-316-4231 to explain the problem and confirm the arrival window and after-hours charges.
Why does high altitude matter on a repair?
Gas equipment must operate within the manufacturer’s requirements for the installation elevation. We check combustion and venting where relevant, because replacing a sensor or control alone may not address the cause of an operating problem.
Do you repair boilers and furnaces on the same call?
We service both types. Tell us which equipment needs attention when booking so we can plan the visit. A furnace heats air through ducts; a boiler supplies hot water to radiators, baseboards, or radiant floors.
Communities we serve
Learn about heating repairs in Santa Fe, Los Alamos, and Española. Call 505-316-4231 to discuss service at your address.
Need heating repairs?
Lobo Tech · NM license 384927 · 1259 Coriander Rd, Santa Fe · 505-316-4231